The configuration details are stored in a text file. If you are using the command line version of Linphone ("linphonec") the configuration file is stored here: "/home/username/.linphonerc". In this example "username" would be replaced by your username, for example if my username is "adam" then I would find the linphonec configuration file in this location: "/home/adam/.linphonerc".
The configuration of the non-command line version (the version with a Graphic User Interface), is done through the interface. However all the settings are stored in a file too, you don't have to touch this file but if you are curious you can find it here: "/home/username/.gnome2/linphone".
If appropriate configuration file doesn't exist, it will be created after starting Linphone. In case of linphonec, the file will be copied from "~/.gnome2/linphone if it exists.
The variables and format is the same for each. The below details each variable:
All settings regarding the local network go here, this includes the speed of the connection and the IP number of the NAT should there be one.
It's a setting to tell linphone how much bandwidth it can use:
0=analog 28k modem
3=minimum ADSL modem
con_type is deprecated and no more used by linphone>=1.4.0, in favour of upload_bw and download_bw.
0=don't use the NAT setting
1=use the NAT setting
This value can be used to override contact header IP. This is usefeul to supress automatival too "smart" IP address selection if you have more IPs. Put the IP number of the NAT router here.
The bandwidth you have available for incoming data. This is noted in kbit/sec. A setting of "0" means unlimited bandwidth. Specific allocations of bandwidth may exclude the use of codecs that require more bandwidth than the setting chosen. Has similar purpose as the con_type. Different codecs are offered in SDP when different bandwidth is available.
The bandwidth you have available for outgoing data. This is noted in kbit/sec. A setting of "0" means unlimited bandwidth. Specific allocations of bandwidth may exclude the use of codecs that require more bandwidth than the setting chosen. Has similar purpose as the con_type. Different codecs are offered in SDP when different bandwidth is available.
STUN is used by Linphone for traversing NAT routers. STUN stands for Simple Traversal of UDP through NATs (Network Address Translation). Linphone can be a STUN client, in which case it will send a request to an external STUN server. The STUN server then tells Linphone the public IP address of the NAT router. It also reports to Linphone which port was opened by the NAT device for incoming traffic. Linphone then uses this information for connecting with a VoIP server or other soft phones.
1= don't use STUN
The address of the STUN server to use. The format will look something like this:
All details regarding your SIP configuration go here. SIP has two kinds of addresses:
The port on your computer that is used for SIP traffic (default is "5060")
0=don't guess the hostname of your computer
1=guess the hostname of your computer (use this if you don't know it)
Put here the SIP Address of Record for your account. The format should be:
This is the timeout setting for incoming calls. If you do not make it to answer an incoming call after the time set here then linphone will timeout. The setting is measure in seconds and the default is "15" (seconds).
0 = don't use SIP INFO messages for DTMFs
1 = use use sip info messages for DTMFs
Essentially there are not enough IP Addresses. An IP Address is the group of numbers that identifies you on the internet, they look something like this: "192.168.0.123". Because there are not enough combinations of these number groups to account for every device that needs to connect to the internet a new way of addressing is being developed, this is called "IPv6". An IPv6 address might look something like this: "E2D6:0000:0000:0000:01B4:7BD8:D0A3:1220"
If you are in a IPv6 network then you can use these addresses instead of the more common IPV4. Linphone is not able to combine different IP protocols at the same time (e.g. SIP over IPv4 and RTP over IPv6).
0 = don't use IPv6
1 = use IPv6
Linphone has a section in the config file for storing different registration server information. These are numbered (starting at zero). Put the number here for the index of the registration setting you wish to use. "-1" means do not use a proxy.
The port number used by the RTP protocol for audio (default 7078)
The port number used by the RTP protocol for video (default 9078)
Number of milliseconds of audio buffered before playing, measured in seconds (default 60).
Number of milliseconds of video buffered before playing, measured in seconds (default 60)
playback_dev_id=ALSA: default device
ringer_dev_id=ALSA: default device
capture_dev_id=ALSA: default device
There has been error in communication with Booktype server. Not sure right now where is the problem.
You should refresh this page.